TRAILER MOVER PLANS *EMAIL*- Heavy Duty or Standard

Description

BUILD THIS TRAILER/POWER MOVER FOR BETWEEN 0 AND 0
THIS LISTING PROVIDED FOR DIGITAL DELIVERY ONLY
(TO PURCHASE-  CONTACT ME THROUGH EBAY WITH YOUR EMAIL ADDRESS AND
TYPE MOVER YOU WANT AND I'LL SEND YOU A PAYPAL INVOICE)
-->
"YOU ARE PURCHASING ONE SET OF "PLANS"
BUILD YOUR OWN CUSTOM POWER MOVER
FEATURES AND SPECIFICATIONS-  STANDARD DUTY
READILY MOVE TRAILERS UP TO 5000 LBS,  7000 LBS ON HARD FLAT SURFACES
SUBSTANCIAL SOLID STEEL FRAME WEIGHS 45 LBS
FRAME AND AXLE CAN CARRY TONGUE WEIGHTS EXCEEDING 1000 LB
USE IT ON DIRT, GRAVEL, CONCRETE OR ASPHALT
POWERED BY A 3000 LB 1.1 HP ATV STYLE WINCH
MAXIMUM SPEED (UNLOADED)~42 FT/MIN
MINIMUM SPEED (FULLY LOADED)~17.8 FT/MIN
3000 LB WINCH PROVIDES 486 LB MOVER FORCE AT 50 PERCENT LOAD, 972 LB AT FULL LOAD
WINCH BRAKE KEEPS MOVER FROM ROLLING WHEN POWER IS REMOVED
EASILY MOVED, FREE-WHEELS WITH WINCH DECOUPLED
RECEIVER STYLE HITCH ALLOWS USE OF DIFFERENT HEIGHT BALL MOUNTS
(Just raise the handle, scoop up the trailer coupler with the hitch ball, lower the handle and you're ready to go.)
A 12 VOLT DEEP CYCLE LEAD ACID BATTERY PROVIDES THE PLENTY OF ENERGY
HANDLE ROTATES VERTICALLY TO MINIMIZE GARAGE STORAGE SPACE REQUIRED
MECHANICAL COMPONENTS INCLUDE SPROCKETS, HUBS, BEARINGS, CHAIN, AXLE, TIRES, RIMS AND WINCH
FEATURES AND SPECIFICATIONS-  HEAVY DUTY:
READILY MOVE TRAILERS UP TO 6000 LBS, 10000 LBS ON HARD FLAT SURFACES
SUBSTANCIAL SOLID STEEL FRAME WEIGHS 45 LBS
FRAME AND AXLE CAN CARRY TONGUE WEIGHTS EXCEEDING 1000 LB
POWERED BY A 3000 LB 1.1 HP ATV STYLE WINCH
MAXIMUM SPEED (UNLOADED)~30 FT/MIN
MINIMUM SPEED (FULLY LOADED)~12.7 FT/MIN
3000 LB WINCH PROVIDES 680 LB MOVER FORCE AT 50 PERCENT LOAD, 1360 LB AT FULL LOAD
PLANS INCLUDE:
DETAILED ASSEMBLY INSTRUCTIONS
DETAILED COMPONENT LIST WITH SUPPLIERS AND PRICES
DETAILED LIST OF STEEL COMPONENTS
8 PAGES OF ASSEMBLY DRAWINGS
APPROXIMATE COST BREAKDOWN*:
WINCH ............................................................................5.00
BEARINGS, AXLE, CHAIN, SPROCKETS....................... 9.00
TIRES AND RIMS ..............................................00-5.00
STEEL..............................................................................00
BATTERY AND CASE .........................................................00
MISC........................... ......................................................00
*  (Prices will vary depending on the particular selection of components and steel availability.    Not all prices shown include shipping)
Feel free to ask me any questions regarding these plans.
I built this simple power mover out of necessity because it was always a trying experience to back up my trailer. This mover makes it easy for one person to manuver a fairly large trailer in and out of tight spaces. It was originally used on decomposed granite to move my 24 foot enclosed trailer through a 10 foot gate and next to the side of my house. I no longer have the enclosed trailer but currently use it to move my flat-bed deck trailer into and out of my tight garage.
The heavy duty version is very similar to the standard version.   It provides 37 percent more force and moves 37 pcrcent slower due to different gearing. Since it moves slower it is easier to control with a heavy trailer during starting and stopping. It also has heavier axle bearings. It uses the same axle and related hardware. Either version can be made with the pneumatic tires on the rear for use on grass and other soft surfaces. To turn the mover with the pneumatic wheels you raise them off the ground using the long handle, turn the mover then set it back down in the new direction.  The plans you will receive will include drawings for both the pneumatic tire version as well as hard rubber casters as on the standard mover. The cost of construction is approximately the same as the standard mover.
It both pushes and pulls with the flip of a switch, and, when you disengage the geared winch it can quickly be rolled to where you want it. The ball mount is interchangeable which allows you to match it to your trailer height. In addition, the handle rotates to a vertical position for storage (see picture).
The construction of this mover is fairly easy. Once you have all the parts you can build it in a weekend. It does require reasonable welding skills and the ability to understand mechanical drawings. There are no difficult machining operations. A chop saw or band saw and drill press are the only heavy tools required.
The mover may be used on slight inclines (up to 6 percent) but it is not recommended for heavy trailers exceeding 2500 lbs on other than flat or near flat surfaces. On loose surfaces the selection of the ball mount should be made to provide all the trailer tongue weight on the drive wheels and minimize the weight on the casters.
EMAIL COPIES WILL BE IN PDF FORMAT AND CAN READILY BE PRINTED ON ANY 8.5X11 printer
PLEASE NOTE-  IF YOU FIND FOR WHATEVER REASON THAT THE EMAIL COPIES ARE INADEQUATE, I CAN SHIP YOU A PAPER COPY FOR ONLY THE DIFFERENCE IN COST.  JUST SEND ME AN EMAIL AND LET ME KNOW.
https://www.youtube.com/watch?v=JwVq1hVFCV4